Turning the table

Turning the table

Shape shifter: The picnic table splits into two benches twobenches (opposite) to suit your space and seating needs.

62

APRIL/MAY 2002

COT TAGE LIFE

...from eating to seating. These convertible benches will knock guests off their feet

Last summer, my wife, Lynn, and I dropped in on cousin Kathleen and her husband, Ross, at their Wahwashkesh Lake cottage. After the customary welcome refreshments and sharing of family news and gossip, Ross and I naturally started talking cottage stuff. I noted that he had recently replaced the deck on the side of the cottage. This required closer observation, so we abandoned the women and our lawn chairs and climbed the steps for the requisite inspection. Ross said he was considering installing a bench along the railing side of the deck and wanted to know what I thought. Since this bench/table project was already under construction back at my place, I suggested it might be a suitable alternative. Like stationary benches, our bench/tables provide extra deck seating space, but they can be moved around. The added bonus is that they can also be quickly converted to half picnic tables or combined to form a full one. This eliminates the need for the traditional, but cumbersome wood picnic table or a plastic or aluminum patio set that always seems to take up too much space. The multi-purpose Cottage Life benches are the hands (and bottoms) down way to go. 1. Refer to the Materials List (p. 68) and Illust. 4 (pp. 66–67), to cut out the main parts. If you do not have a really good sabre/jig saw, or access to a band saw, you might want to mitre the corners instead of cutting the curves. It is virtually impossible to keep the blade perpendicular with a standard sabre/jig saw in 11⁄ 2" lumber so save yourself the aggravation. 2. The table legs require a 11 ⁄ 2" x 31 ⁄ 2" notch for the back brace (Illust. 4). I accomplished this with a dado blade on my radial arm saw. However, the same can be achieved with a circular saw (or a handsaw, for that matter) and a sharp chisel: Make several passes 11 ⁄ 2" deep and then remove the remaining material with the chisel. The bottom outside corners of all four legs for each bench are trimmed to reduce the possibility of splitting when the table is tipped (Illust. 4). Drill a 3 ⁄ 8" hole, centred, 31 ⁄ 2" from the top of each table leg. >> FRAMING/LEGS

B Y WAY N E L E N N O X P H OTO G R A P H Y BY J . M I C H A E L L A FO N D T E C H N I C A L I L L U S T R A T I O N S B Y T E R R Y D O VA S T O N A N D B A R B D I P I E T R O

COT TAGE LIFE

APRIL/MAY 2 0 0 2

63

3. For this project, I opted to fashion 31⁄2"-wide half-lap joints in the bench end brackets to increase the frame’s rigidity and strength. Remember to make two pairs of opposing brackets (Illust. 4, p. 66). Again, the circular saw and chisel method can be used to make the notches if you don’t have something better. Drill the eight clearance holes in each bracket. I rummaged around in my rather sorry collection of bits and found only a 9 ⁄ 64" – adequate enough for #8 screws! For looks, you can router the outside perimeter of each bracket Back-up surface: (Illust. 3, p. 65). I like my trusty The bench backrest swings old 1⁄2" roundover bit because it up to form half-tables. produces such a pleasing profile. 4. Sand the bench legs, table legs, and the bench end brackets. Attach the legs to the bench end brackets with 17" #8 x 2" deck screws (the brassy-looking kind) and Type II carpenter’s glue (Illust. 1). The advantage of Type II glue is its water resistance. However, it runs more and tends to ooze out of the joints longer than ordinary wood glue so you’ll 131⁄2" need to be extra careful when wiping it up. 5. Drill the 3 ⁄ 8" holes in the table end 29" brackets where shown (Illust. 4, p. 66). Router the outside and inside perimeters, except along the top edges, of the four clearance holes table end and two table centre brackets. for leg braces 121⁄4" TABLETOP 1. Select the six best 2" x 6" x 711 ⁄ 2" boards for the tabletops. Illustration 1 Round the outside corners of the four outside boards as in Illust. 2. To enable compression nuts. Make it a good snug the two benches to fit together to form a I then had to remove the innermost fit (no Herc, you don’t need to crush the large table, the table legs must be offset boards to router them.) Ensure that the cedar!). Carefully stand the benches (see photo, p. 62). For Bench A, the frames are square, and screw the boards to upright, and swing the tabletop/bench clearance holes for the table end bracket the bench end brackets using #8 x 3" deck backs up into the tabletop position. are located 4 1 ⁄ 2" from the ends of the screws, leaving about 1⁄ 2" between boards. BENCHES 1. Select the six bench tabletop; for Bench B, they are drilled 3. Router the outside edges of the bench boards (four 2" x 4" x 711 ⁄ 2" and two 6 1 ⁄ 2" from the end. The holes for the centre brackets and the leg braces before centre brackets do not need to be offset 2" x 6" x 711 ⁄ 2"). Round the outside cor- assembly. I screwed the brackets in from ners of the four 2" x 4"s. (Illust. 2). Sand the table boards and the underneath; countersink the holes a 2. Drill the clearance holes for the bench good 1 ⁄ 2" because you will only be using six table brackets. Check for square, and end brackets in the bench boards. Again, #8 x 2" deck screws. Drill the clearance screw the boards to the brackets using holes in the bench legs (Illust. 1) and because the frames are offset, the clear#8 x 3" deck screws. Leave about a 3⁄8" gap between each board to achieve the 17" attach the bench leg braces to the centre ance holes for Bench A and Bench B are overall width for each table (Illust. 1). bench boards and to the legs with #8 x 3" different (Illust. 2). While you’re at it, 2. Turn the assembled tabletop pieces drill the clearance holes for the bench leg deck screws. Sand. BACK BR ACES The back braces upside down. Attach the table leg assem- braces as well. Router the top perimeter (Illust. 4, p. 67) measure 633 ⁄ 4" for bly to the inside of the table end brackets of each board before assembly. (I, natuBench A and 593 ⁄ 4" for Bench B. Each with 3 ⁄ 8" x 4" carriage bolts, washers, and rally, made the mistake of assembly first; 64

APRIL/MAY 2002

COT TAGE LIFE

Illustration 2

711⁄2"

61⁄2"

35 ⁄ " 34

41⁄2"

Bench

5 1 ⁄2 "

Bench

A

A

Bench

Bench

TABLETOP

B

B

5 1 ⁄2 "

round outside corners

5 1 ⁄2 "

3 1 ⁄2 " BENCH

51⁄2" 3 1 ⁄2 "

101⁄2" 13"

Bench A (for Bench B , 121⁄2" and 15")

5 3 ⁄8 " 7 3 ⁄8 "

carriage bolt

table end bracket

router outside perimeter of end brackets only

bench leg brace

Illustration 3

brace extends about 11 ⁄ 2" beyond the table legs. Notches (see inset detail, p. 67) on the extensions act as stops for the tabletops when they are tipped up, and the extensions themselves stop the bench backs when they’re tipped down. The measurements given for the notches are starting points. Begin conservatively and whittle away a bit at a time, checking for fit as you go. I made the initial cuts with a backsaw, but then I had to make several fittings, adjusting the angles with a rasp and a very sharp chisel to get them just right; be patient. Once you’re satisfied, check for square, sand, then glue and screw the braces to the table legs using two #8 x 3" deck screws at each end.

1. When the bench back is tilted down, it needs to be secured; it must also be locked when it is in the table position. Illust. 5 and 6 (p. 67) show details of the locking mechanism that satisfies both requirements (a eureka moment at five in the morning). The stop block (Illust. 5) has been routered to match the profile of the table centre bracket. Install it on the back brace directly below the centre bracket with glue and two #8 x 3" deck screws. 2. Make a 1⁄ 2" notch in the bottom of the stop block with a round file or a surform tool. Taper the leading edge of the notch to create a flat surface that is roughly level with the tabletop. (The notch on the top for the bench position is added later.) LOCKING MECHANISM

3. The swingarm assemblies consist of 1 3 4" x 1 ⁄ 2" x 12 ⁄ 4" sides, rounded at the ends, and joined by three 1⁄ 2" x 21⁄ 2" dowels, two on the bottom and one on top. The dowels nest in 1 ⁄ 2" pockets drilled 7 ⁄ " deep (a forstner-type bit is ideal for 16 this job, as is a drill press). Drill a small clearance hole through the centre of each pocket. This allows excess glue to escape from the pocket during assembly, and is the guide for the pilot holes that you will need to drill for the #6 x 1" screws. Temporarily assemble the swingarm by securing both sides to the two bottom dowels only. Ours were approximately 71⁄ 16" and 87 ⁄ 8" down from the top of the arm. 4. With the bench back in the tabletop position (clamped to hold it in place, if 3⁄

COT TAGE LIFE

APRIL/MAY 2 0 0 2

65

necessary), position the swingarm so that the top of the middle dowel you just installed fits snugly into the notch you cut in the bottom of the stop block (left-hand photo, opposite). Then slide the open upper end of the assembly over the table centre bracket. Use a small nail or awl to mark the position where the upper dowel will pass through the table centre bracket (that little hole you drilled will help. The position indicated in Illust. 6 is approximate). Drill a 1 ⁄ 2" hole through the table centre bracket (if you are using a drill press, you will have to remove the bracket from the table). Slide the top dowel piece through the hole in the bracket, sanding the hole slightly, if necessary, to get a nice fit. 5. Leaving the upper dowel in place, pull the swingarm apart, sand, add glue to the pockets, and reassemble. Screw the swingarm sides to the dowel pieces with #6 x 1" screws. Use a rasp or surform to adjust the fit of the middle dowel against the notch in the bottom of each stop block (Illust. 6). 6. With the swingarm in place, drill a centred hole through it and the stop block for the pin. (Precise placement isn’t important: The pin is not loadbearing; it functions simply to hold the swingarm in place.) I made the pins from 3 ⁄ 8" x 8" eye bolts. Cut the threaded portion off and taper the ends with a flat file to remove sharp edges and to make for a smoother fit. Though the threaded part measures 3 ⁄ " in diameter, the smooth shank is 8 slightly smaller; start with a 21 ⁄ 64" hole. If that is too tight, then move up to 11 ⁄ ", and so on. 32 7. Pull the pin and slide the swingarm out. Tip the tabletop into its bench position. Carefully cut a new notch in the top of the stop block until the bottom dowel can be seated securely (this will prevent the bench back from moving). The notch must be deep enough so that you can drill a second hole through the bottom of the swingarms for the pin (right-hand photo, opposite). 8. Run a 12" length of open-link light chain through the eye of the pin, spread a link and hook it back on itself, then close the link. Screw the other end of the chain to the back brace with a #6 x 1" screw. >> 66

APRIL/MAY 2002

COT TAGE LIFE

29"

11⁄2"

3

⁄4"

101⁄2"

clearance holes

R13⁄4"

31⁄2"

half-lap joint

115⁄8"

31⁄2"

22.5°

17.5°

BENCH END BRACKET (x2) (left side shown; for right bracket create an opposing, mirror-view piece x2)

16"

⁄ " hole

38

31⁄2"

35⁄8" 51⁄2"

8" TABLE END BRACKET (x4)

121⁄2"

11⁄2" BENCH CENTRE BRACKET (x2)

45°

R13⁄4"

31⁄2"

3 1 ⁄2 " ⁄ " hole

38

notch for back brace 17.5° 11⁄2" 211⁄4" 30" 31⁄2"

BENCH LEG (x4)

16 ⁄8" 3

31⁄2"

legs trimmed

TABLE LEG (x4)

22.5°

16"

BACK BRACE DETAIL

31⁄2"

⁄"

14

31⁄2"

R13⁄4"

31⁄2"

TABLE CENTRE BRACKET (x2)

45°

23⁄4"

21⁄4"

11"

31⁄2" BENCH LEG BRACE (x4)

A 633⁄4" B 593⁄4" BACK BRACE (x1 of each)

Illustration 4

LOCKING MECHANISM Illustration 6

stop block

11⁄2"

The swingarm locks the tabletop (left) and the bench (right) in position .

55⁄8" 71⁄16"

123⁄4"

table centre bracket

8 7 ⁄8 "

3"

111⁄8"

back brace

15⁄8"

pin hole for bench position

(approx.)

R13⁄4"

pin hole for table position

dowel

31⁄2" 1"(approx.) 11⁄2"

R1⁄2"

STOP BLOCK (x2)

3

⁄4" 31⁄8"

Illustration 5 COT TAGE LIFE

these measurements are all approximate

APRIL/MAY 2 0 02

67

TABLE LATCH MECHANISM Illustration 7

11⁄2"

Illustration 8

1"

#8 x 2" deck screws taper edge 5 3 ⁄4 "

2"

33⁄4"

1 1 ⁄2 " 3

5 3 ⁄4 "

3" A

⁄4 " TABLE CATCH (x2)

3" B

1⁄" 14

1 1 ⁄2 " 11" A

⁄"

12

1 1 ⁄2 "

dowel

1⁄"

TABLE LATCH (x2)

Materials List (for two benches) Part

Cutting list

Tabletop boards

2" x 6" x 71 1 ⁄ 2"

2

Centre bench boards

2" x 6" x 71 1 ⁄ 2"

2

Tabletop boards

2" x 6" x 71 1 ⁄ 2"

4

Table end brackets

2" x 6" x 16"

4

Back brace – Bench A

2" x 4" x 63 3 ⁄ 4"

1

Back brace – Bench B

2" x 4" x 59 3 ⁄ 4"

1

Table centre brackets

2" x 4" x 16"

2

Qty

Table legs

2" x 4" x 30"

4

Outside bench boards

2" x 4" x 71 1 ⁄ 2"

4

Bench legs

2 " x 4 " x 1 6 3 ⁄ 8"

4

Bench end brackets

2" x 4" x 29"

4

Bench leg braces

2" x 4" x 11"

4

Bench centre brackets

2" x 4" x 12 1 ⁄ 2"

2

Stop blocks

2" x 3" x 4"

2

Swingarms

3⁄

4"

Table latches

1⁄

1 2" x 1 ⁄ 2" x 11"

Table catches

1⁄

2"

x 11⁄ 2" x 12 3⁄ 4" x 1 1 ⁄ 2" x 8 3⁄ 4"

4 2 2

*All lumber is premium western red cedar

Hardware Deck screws

#8 x 2"

1 lb

Deck screws

#8 x 3"

1 lb

Wood screws

#6 x 1"

14

Wood screws and washers

#12 x 1 1 ⁄ 2"

2

Eye bolts

3⁄

2

8" x 8"

Finishing nails

1"

Carriage bolts with washers

3⁄

8"

4 x 4"

4

x 2'

1

and compression nuts Light open-link chain

1'

Hardwood dowel

1⁄

2"

Varathane Natural Oil Finish Type II carpenter’s glue

68

B

38

APRIL/MAY 2002

COT TAGE LIFE

2 2L

Material 2" x 6" x 12' (x2)

2" x 6" x 8' (x4)

2" x 4" x 14' (x1)

2" x 4" x 10' (x6)

ripped from 2" x 4" offcuts

9. Swing the tabletop back up and lock it into position. Router the outside perimeter only of the tabletops (Illust. 2, p. 65). I free-handed this operation, trying to be careful not to run into the gaps, but a cedar shim or a piece of 3⁄ 8" scrap plywood wedged into the gap – flush to the top and end – will prevent the router bit from wandering into this space. Sand. TABLE LATCHES A simple latch ensures that when the benches are combined to form a single picnic table, the tabletop surfaces stay together (Illust. 7 and 8, above). It is nowhere near as inspired as the tabletop lock, but it works. Rip 1 ⁄ 2"-thick strips of 2" x 4" for the latches and the catches. A 1 3⁄ 4" piece of dowel is recessed into the swinging latch arm. The illustrations show how these are assembled. Tack the catches together with 1" finishing nails. Use a #12 x 11 ⁄ 2" screw for the latch because it will resist turning. (Note that the two tables should be separated before you move them.) FINISH I finished the tables with two coats of Varathane Natural Oil Finish. This product provides protection from the elements and preserves the cedar’s terrific appearance. It is also really easy to apply – ain’t that a bonus! L Long-time contributor Wayne Lennox also created the adjustable dock tray in the July/Aug. ’01 issue and the oftreplicated outhouse in July/Aug. ’99.